Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
- 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
   10.2. General information
   + 10.3. Accelerator cable
   10.4. Air filter
   10.5. Casing of the air filter
   10.6. Fuel filter
   10.7. Pressure accumulator
   10.8. Fuel level sensor
   10.9. Fuel pump
   10.10. Fuel tank
   10.11. Throttle case
   10.12. Inlet collector
   + 10.13. Elements of system of injection of KE-JETRONIC fuel
   10.14. Pressure removal in fuel system
   10.15. Adjustment of turns of idling and the contents WITH in exhaust gases
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






10.12. Inlet collector

Removal

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Remove pressure in fuel system.
3. Remove an accelerator cable from the directing lever of a butterfly valve. On models with an automatic transmission disconnect from draft of a throttle a cable of management of pressure. On models with a control system of speed of movement of the car remove draft of an accelerator from the block of the executive mechanism of a throttle.
4. Remove a plait of wires and unscrew an arm of a plait of wires from an inlet collector.
5. Unscrew a tube for щупа measurements of level of engine oil.
6. Remove the air filter.
7. On all models, except models with 6-cylinder DOHC engines remove from an inlet collector the valve of cold start.
8. Remove the fuel highway and the sensor of a stream of air.
9. Remove the throttle case.
10. On models with 6-cylinder SOHC engines with a control system of speed of movement of the car unscrew from an inlet collector the executive mechanism of a throttle together with an arm.
11. On models with 4-cylinder engines mark and disconnect hoses from the distributor of a stream of air on idling turns.
12. Unscrew a connecting nut and disconnect from a collector a vacuum hose of the vacuum amplifier of brakes.
13. Mark and disconnect from an inlet collector remained электричес cues sockets and vacuum hoses.
14. Unscrew and remove arms of support of an inlet collector. Check that anything else does not interfere with removal of an inlet collector.
15. Unscrew nuts and bolts and remove an inlet collector from a head of the block of cylinders. Remove laying of an inlet collector.
16. If necessary unscrew bolts and divide the top and bottom parts of an inlet collector. At assembly of the top and bottom parts of an inlet collector it is necessary to use new laying.
17. Being careful and using a plastic or wooden scraper, clear interfaced surfaces of a head of the block of cylinders and an inlet collector.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal taking into account the next moments.
2. Check that interfaced surfaces of an inlet collector and a head of the block of cylinders are cleared of traces of old laying.
3. Adjust an accelerator cable.
4. On models with an automatic transmission adjust work of a cable of management as pressure.
5. Check and, if necessary, adjust idling turns.