Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
- TRANSMISSION
   18.2. General information
   18.3. Coupling knot
   18.4. Lever of switching off of coupling and vyzhimny bearing
   18.5. Working cylinder of coupling
   + 18.6. Main cylinder of coupling
   18.7. Air removal from hydraulic system of coupling
   18.8. Coupling pedal
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






18.4. Lever of switching off of coupling and vyzhimny bearing

VYZHIMNA BEARING

Removal

Removal of the vyzhimny bearing

PERFORMANCE ORDER
1. Remove a transmission.
2. Turn vyzhimny the bearing and disconnect it the lever of switching off of coupling, then move the bearing forward on directing plug and remove from it from primary shaft of a case of coupling (see fig. Removal of the vyzhimny bearing).

Check

PERFORMANCE ORDER
1. Check the bearing of switching off of coupling on uniformity and softness of a course, and wear existence.
2. If operating time of the bearing is not known, it is desirable to replace it.
3. Do not wash out the bearing in solvents as it will lead to removal from the bearing of greasing and to fast wear of the bearing.

Installation

PERFORMANCE ORDER
1. Clear and grease with a thin layer of greasing on the basis of a molybdenum disulfide a surface of the lever of switching off of the coupling, interfaced to the vyzhimny bearing, and directing plug.
2. Establish vyzhimny the bearing on directing plug, then, having turned it, connect to the lever of switching off of coupling.
3. Establish a transmission.

LEVER OF SWITCHING OFF OF COUPLING

Removal

Removal of the lever of switching off of coupling

PERFORMANCE ORDER
1. Remove vyzhimny the bearing.
2. Move a pusher of the executive cylinder of coupling forward, then release a sharnirny finger from the lever of switching off of coupling and remove the lever from the directing plug (see fig. Removal of the lever of switching off of coupling).

Check

PERFORMANCE ORDER
1. Clear the lever of switching off of coupling, a hairpin with a spherical tip and directing plug and check their condition.
2. Check a condition of a fixing spring on the lever of switching off of coupling.

Installation

Drawing of a layer of greasing on a sharnirny finger and directing plug
Before installation of the lever of switching off of coupling apply a thin film greasings on the basis of a molybdenum disulfide on a sharnirny finger and directing plug.

Installation of the lever of switching off of coupling
At installation of the lever of switching off of coupling check, that the fixing spring accurately held a sharnirny finger.

PERFORMANCE ORDER
1. Clear and apply a thin film greasings on the basis of a molybdenum disulfide on the surface of the lever interfaced to the vyzhimny bearing, and also on a sharnirny finger and directing plug (see fig. Drawing of a layer of greasing on a sharnirny finger and directing plug).
2. Establish the lever of switching off of coupling on directing plug, then move the lever end on a sharnirny finger so that the fixing spring was established on a place and held a sharnirny finger (see fig. Installation of the lever of switching off of coupling).
3. Establish vyzhimny the bearing.