W124 Mercedes + Governing bodies and control devices + MAINTENANCE + 2. Maintenance (diesel engines) + ENGINE + 4. Repair of 6-cylinder petrol SOHC engines + 5. Repair of 6-cylinder petrol DOHC engines + 6. Repair of the diesel engine established in the car + 7. Major maintenance of engines + COOLING SYSTEM + FUEL SYSTEM + 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC) + 11. System of injection of BOSCH HFM fuel + 12. Fuel system of diesel engines + 13. Fuel system of diesel engines + SYSTEMS OF START, IGNITION + 15. System of ignition of 4-cylinder petrol engines + 16. System of ignition of four-cylinder petrol engines + PRESTARTING HEATING + TRANSMISSION - 19. Mechanical transmission 19.2. General information 19.3. Oil replacement in a transmission 19.4. Gear shifting mechanism 19.5. Replacement of sealing rings 19.6. Switch of light of a backing 19.7. Removal and transmission installation 19.8. Transmission repair + 20. Automatic transmission + POWER SHAFTS + BRAKE SYSTEM + SUSPENSION BRACKET + BODY + ELECTRIC EQUIPMENT + CHECK OF MALFUNCTIONS
|
GEAR SHIFTING LEVER
Removal
Removal of a spring latch from the gear shifting lever
PERFORMANCE ORDER |
1. Remove up on the lever a protective cover of the lever of gear shifting from the central console. |
2. Using a screw-driver edge, wring out the spring latch, fixing the gear shifting lever (see fig. Removal of a spring latch from the gear shifting lever). |
3. Having pulled up, take the gear shifting lever. |
|
Installation
PERFORMANCE ORDER |
1. Installation is made in sequence, return to removal. Check correctness of installation and reliability of fixing of a spring latch. |
|
LEVERS OF THE CHOICE OF TRANSFERS
Removal
PERFORMANCE ORDER |
1. Lift a forward part of the car and fix on supports. |
2. Working under the car, remove spring brackets and disconnect drafts from levers of a choice of transfers. |
3. Working in car salon, remove decorative overlays of the central console for access to levers of a choice of transfers. |
4. Remove from an arm the switch of light of a backing. |
5. Unscrew a bolt of fastening of knot of levers of a choice of transfers. |
6. Disconnect from knot of levers of a choice of transfers a cable of the hand brake. |
7. Take assembly of levers of a choice of transfers to car salon. Remove laying. |
|
Installation
PERFORMANCE ORDER |
1. Installation is made in sequence, return to removal. Check that both fastenings are reliably fixed and check adjustment of drafts. |
|
Adjustment
Prevention
For carrying out adjustment use of a special adjusting pin is necessary.
Fastening of bent for to levers of a choice of transfers
The sizes of an adjusting pin for adjustment of drafts of gear shifting (all sizes in millimeters)
Arrangement of an adjusting pin in levers of a choice of transfers
|
A–adjusting pin;
B–driveshaft |
PERFORMANCE ORDER |
1. Lift a forward part of the car and fix on supports. |
2. Establish the gear shifting lever in neutral situation. |
3. Working under the car, remove brackets of fastening and disconnect drafts from levers of a choice of transfers (see fig. Fastening of bent for to levers of a choice of transfers). |
4. Make an adjusting pin according to the sizes presented in drawing the Sizes of an adjusting pin for adjustment of drafts of gear shifting. |
5. Insert an adjusting pin through openings in levers of a choice of transfers (see fig. An arrangement of an adjusting pin in levers of a choice of transfers). |
6. After fixing by an adjusting pin of levers of a choice of transfers establish drafts of gear shifting on pins of levers. If necessary adjust length of drafts of gear shifting for what weaken a lock-nut and, rotating a tip, establish the demanded length of draft then tighten a lock-nut. |
7. After carrying out adjustment establish brackets of fastening and fix drafts on levers, then take an adjusting pin. |
8. Lower the car on wheels and check work of drafts of gear shifting. |
|
|
|