Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
- 19. Mechanical transmission
   19.2. General information
   19.3. Oil replacement in a transmission
   19.4. Gear shifting mechanism
   19.5. Replacement of sealing rings
   19.6. Switch of light of a backing
   19.7. Removal and transmission installation
   19.8. Transmission repair
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






19.5. Replacement of sealing rings

Sealing ring of an entrance shaft

Removal of a protective cover from a forward part of a case of coupling

Removal of sealing laying from a protective cover

Arrangement of a sealing ring of an entrance shaft in a protective cover

PERFORMANCE ORDER
1. Remove a transmission.
2. Remove vyzhimny the bearing and the lever of switching off of coupling.
3. Unscrew bolts of fastening and remove a protective cover from a forward part of a case of coupling (see fig. Removal of a protective cover from a forward part of a case of coupling).
4. From a back part of a cover remove sealing laying (see fig. Removal of sealing laying from a protective cover).
5. Using a screw-driver edge as the lever, remove a sealing ring from a cover (see fig. An arrangement of a sealing ring of an entrance shaft in a protective cover).
6. Being careful, clear a nest of a sealing ring in a protective cover. Using a tubular opravka of the corresponding diameter, establish a new sealing ring in a cover.
7. Grease and establish in a protective cover sealing laying, then, being careful, establish a protective cover on a coupling case.
8. Put on a carving of bolts of fastening of a protective cover a thin layer of the means interfering unscrewing of bolts. Screw in bolts and tighten them the demanded moment.
9. Establish the lever of switching off of coupling and vyzhimny the bearing.
10. Establish a transmission on the car.

Sealing ring of a target flange


Prevention

At installation it is necessary to use a new nut of fastening of a target flange of a transmission.


Removal of a nut of fastening of a target flange of a transmission

PERFORMANCE ORDER
1. Disconnect the driveshaft from a target flange of a transmission.
2. Establish the gear shifting lever in neutral situation.
3. Using the special tool, fix a target flange of a transmission from a provorachivaniye. Thus access to a nut of fastening of a target flange should be free.
4. Unscrew a nut of fastening of a target flange of a transmission. At installation it is necessary to use a new nut (see fig. Removal of a nut of fastening of a target flange of a transmission).
5. Using a stripper, remove a target flange from a transmission shaft.
6. Using a screw-driver edge as the lever, take a sealing ring of a target flange of a transmission.
7. Being careful, clear a nest for a sealing ring.
8. Using a tubular opravka of the corresponding diameter, establish a new sealing ring of a target flange.
9. Establish a flange on a target shaft of a transmission and fix it a new nut. At a nut tightening, using the special tool, hold a flange from a provorachivaniye.
10. Connect the driveshaft to a target flange of a transmission.