Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
- MAINTENANCE
   1.2. Periodicity of service
   1.3. Maintenance
   - 1.4. Each 9 000 km
      1.4.1. 4-cylinder engines
      1.4.2. 6-cylinder SOHC engines
      1.4.3. 6-cylinder DOHC engines
   + 1.5. Each 18 000 km
   1.6. Each 58 000 km
   1.7. Each 118 000 km or 1 time in 4 years
   1.8. Each 12 months
   1.9. Each 3 years
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






1.4.2. 6-cylinder SOHC engines

GENERAL INFORMATION

Places of drawing of a thin layer of engine oil on rubber consolidation of the new oil filter

Stopper arrangement plum of engine oil on the 6-cylinder SOHC engine

PERFORMANCE ORDER
1. Use the special tool to weaken the oil filter, then unscrew it a hand.
2. Wipe all traces of oil and dirt round a place of fastening of the filter. Check, whether there was a rubber consolidation on the block of cylinders. If it remained, remove it.
3. Grease with a thin layer of engine oil rubber consolidation of the new oil filter and screw up the filter a hand, without using any tools (see fig. Places of drawing of a thin layer of engine oil on rubber consolidation of the new oil filter).
4. Weaken a drain stopper approximately on a turn half (see fig. A stopper arrangement plum of engine oil on 6-цилиндро the vy SOHC engine). Place the container for oil plum under a drain stopper and unscrew a stopper completely. If it is necessary, press a stopper when unscrew that oil did not proceed prematurely. Remove ring consolidation from a masloslivny stopper.
5. When oil completely will flow down, wipe everything round a drain opening a rag and reliably screw up a stopper into place.
6. Establish the car on an equal horizontal surface.
7. Take щуп for measurement of level of oil and remove a stopper from a maslozalivny mouth.
8. Fill in oil in the engine, using the corresponding grade of oil. Fill in a half of necessary amount of oil and wait some minutes that oil flew down in the pallet. Then continue to pour oil in the small portions while level of oil will not reach a minimum level on щупе. At addition about 1 more liter level of oil will rise to maximum on щупе. Close a cover of a jellied mouth.
9. Start the engine and let's to it work some minutes. Check it about leakages of oil round the filter and a drain stopper on the pallet. Keep in mind that the control bulb of pressure of oil can burn some seconds as oil should fill all channels and oil capacities in the engine.
10. Switch off the engine and wait some minutes that oil flew down in the pallet. Check level of oil and add, if it is necessary.