Mercedes W124

since 1985-1995 of release

Repair and car operation

W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
- 20. Automatic transmission
   20.2. General information
   20.3. Selector lever
   20.4. Draft of a choice of transfers
   + 20.5. Adjustment of a cable of management by pressure
   - 20.6. Switches of blocking of a starter and backing lamps
      20.6.2. Models with a transmission 722.4
   + 20.7. Removal and installation of an automatic transmission
   20.8. Repair of an automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS

20.6. Switches of blocking of a starter and backing lamps

20.6.1. All models, except models with a transmission 722.4

Removal

Extraction of a bracket of fastening of the electric socket (shooter) of the switch of blocking of a starter and backing lamps on all models, except models with a transmission 722.4

A–draft of gear shifting;

B–lever of a choice of transfers;

C–electric socket

Extraction of the screw of fastening of the lever of a choice of transfers to a transmission

Removal of the lever of a choice of transfers from a transmission

Removal of the switch of blocking of a starter and backing lamps from a transmission

PERFORMANCE ORDER

1. Remove a weight wire from the accumulator.

2. Tighten the hand brake, then lift a forward part of the car and fix on supports.

3. Release a bracket of fastening of the electric socket of the switch of blocking of a starter and backing lamps (see fig. Extraction of a bracket of fastening of the electric socket of the switch of blocking of a starter and backing lamps on all models, except models with a transmission 722.4).

4. Remove a bracket and disconnect draft from the lever of a choice of transfers on a transmission.

5. Using two screw-drivers and being careful, remove the electric socket from the switch of blocking of a starter and backing lamps.

6. Unscrew the screw and a nut of fastening of the lever and remove the lever from a transmission (see fig. Extraction of the screw of fastening of the lever of a choice of transfers to a transmission, Removal of the lever of a choice of transfers from a transmission).

7. Unscrew screws and remove the switch of blocking of a starter and backing lamps from a transmission (see fig. Removal of the switch of blocking of a starter and backing lamps from a transmission).

Installation and adjustment

Installation of a shaft of a drill in diameter of 4 mm in an opening of the lever and a reference point of the switch of blocking of a starter and backing lamps

Arrangement of screws of fastening of the switch of blocking of a starter and backing lamps

PERFORMANCE ORDER

1. Establish the switch of blocking of a starter and backing lamps into place, insert and screw up screws, without tightening them it is final.

2. Establish the lever of a choice of transfers on a transmission so that the reference point on the switch was established in the corresponding opening in the lever. Check that the lever of a choice of transfers is in situation N. Marking of provisions is available on a transmission case. Fix the lever of a choice of transfers by the screw and a nut.

3. Insert a shaft of a drill or a steel core in diameter of 4 mm into an opening of the lever and a switch reference point. Thus the steel core should enter into an opening in the switch case (see fig. Installation of a shaft of a drill in diameter of 4 mm in an opening of the lever and a reference point of the switch of blocking of a starter and backing lamps).

4. In this situation finally tighten screws of fastening of the switch, then get a drill or a core (see fig. Arrangement of screws of fastening of the switch of blocking of a starter and backing lamps).

5. Connect draft to the lever of a choice of transfers and fix it a bracket.

6. Connect the electric socket to the switch and fix it a bracket.

7. Lower the car and connect a weight wire.