Mercedes W124

since 1985-1995 of release

Repair and car operation

W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
- BRAKE SYSTEM
   22.2. General information
   22.3. Pumping of hydraulic brake system
   22.4. Brake pipelines and hoses
   + 22.5. Replacement of forward brake shoes
   22.6. Replacement of back brake shoes
   22.7. Forward brake disk
   22.8. Back brake disk
   22.9. Forward brake support
   + 22.10. Support repair
   22.11. Back brake support
   22.12. Main brake cylinder
   22.13. Vacuum amplifier of brakes
   22.14. Unilateral valve of the vacuum amplifier of brakes
   22.15. Adjustment of the parking brake
   22.16. Brake shoes of the parking brake
   22.17. Pedal of the parking brake
   22.18. Cables of the parking brake
   22.19. Stoplight switch
   22.20. Anti-blocking system (ABS)
   - 22.21. Elements of anti-blocking system
      22.21.1.2. Electronic control device (ECU)
      22.21.1.3. Sensor of a forward wheel
      22.21.1.4. Sensor of a back wheel
      22.21.1.5. Gear rotor of sensors of wheels
      22.21.1.6. Relay
      22.21.2. Models with a control system of speed of movement of the car (ASR)
      22.21.2.2 ASR system pump
      22.21.2.3 Pressure accumulator
      22.21.2.4 Electronic control device (ECU)
      22.21.2.5 Sensor of a forward wheel
      22.21.2.6 Sensor of a back wheel
      22.21.2.7 Gear rotor of sensors of wheels
      22.21.2.8 Relay
   22.22. The vacuum pump on models with diesel engines
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS

22.21.2.6 Sensor of a back wheel

GENERAL INFORMATION

Prevention

At installation of the sensor of a back wheel it is necessary to use a new bolt of fastening of the sensor and a new nut of the mechanism of reverse main gear, and also a new sealing ring of the sensor.

Removal

PERFORMANCE ORDER

1. Lift a back part of the car and fix on supports.

2. Unscrew nuts and remove a casing, fixing sensor electroconducting to the car bottom.

3. Establish a jack with wooden whetstone under a case of reverse main gear and raise a jack so that the weight of reverse main gear was perceived by a jack.

4. Unscrew two nuts and take two bolts, fixing a back part of the main transfer.

5. Unscrew a nut and take a bolt, fixing a forward part of the main transfer.

6. Being careful, omit reverse main gear so that the driveshaft only concerned a cross-section basic beam. Note an arrangement and remove washers and rubber pillows from forward fastening of reverse main gear. Check a condition of rubber pillows and, if necessary, replace them.

7. Unscrew a bolt and remove the sensor together with a sealing ring from a case of reverse main gear. Replace a sealing ring of the sensor.

8. Define a site of the electric socket of the sensor and uncover the electric socket. Turn a lock ring and disconnect the electric socket.

9. If it is necessary to remove both sensors at the same time, mark wires and electric sockets of sensors.

Installation

PERFORMANCE ORDER

1. According to earlier made marking connect electric sockets of the sensor and establish a cover.

2. Clear interfaced surfaces of the sensor and a case of reverse main gear and establish new sealing rings of sensors.

3. Establish sensors on a case of reverse main gear and fix bolts, having tightened them the demanded moment.

4. Check that rubber pillows and washers are correctly established on a forward part of reverse main gear and establish reverse main gear to a starting position.

5. Fix reverse main gear by bolts, having screwed on them new nuts and having tightened them the demanded moment.

6. Check correctness of an arrangement of electroconducting of sensors, then establish on electroconducting a casing and lower the car.