Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
- SUSPENSION BRACKET
   23.2. General information
   23.3. Bearing of a forward nave
   23.4. Nave of a forward wheel
   23.5. Rotary fist
   23.6. Shock-absorber of a forward suspension bracket
   23.7. Spring of a forward suspension bracket
   23.8. Bottom lever of a forward suspension bracket
   23.9. Forward stabilizer of cross-section stability
   23.10. Fixing element of a back nave
   23.11. Replacement of the bearing of a back nave
   + 23.12. Shock-absorber of a back suspension bracket
   23.13. Spring of a back suspension bracket
   + 23.14. Levers of a back suspension bracket
   23.15. Bottom lever of a back suspension bracket
   23.16. Stabilizer of cross-section stability of a back suspension bracket
   23.17. Connecting earring of the stabilizer of cross-section stability
   23.18. System of a being self-leveled back suspension bracket on the Versatile person models
   + 23.19. Elements of a being self-leveled back suspension bracket
   23.20. Steering wheel
   23.21. Steering column
   23.22. Lock steering column / lock of ignition
   23.23. Contact group of the lock of ignition
   23.24. Rubber coupling of a steering shaft
   23.25. Steering transfer
   23.26. Soshka of steering transfer
   23.27. Replacement of the bottom sealing ring of steering transfer
   23.28. Pump of the amplifier of a steering
   23.29. Pumping of system of the amplifier of a steering
   23.30. Steering shock-absorber
   23.31. Central steering draft
   23.32. Intermediate lever of a steering
   23.34. Spherical hinges of cross-section steering draft
   23.35. Cross-section steering draft
   23.36. Corners of installation of wheels
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






23.11. Replacement of the bearing of a back nave

GENERAL INFORMATION

Prevention

For removal of the bearing of a back nave it is necessary to use a hydraulic press and tubular opravka of the corresponding diameter. In the absence of a press it is possible to use a big metalwork vice. Internal rings of the bearing are pressed on the nave plug. If at bearing removal its internal ring remains on the nave plug, for removal of this ring it is necessary to use a stripper.


PERFORMANCE ORDER
1. Remove a fixing element of a back nave.
2. Using the corresponding opravka, establish a fixing element of a nave on a table of a hydraulic press and, being careful, squeeze out a nave from the bearing. If the internal ring of the bearing remained on the nave plug, remove it with stripper application.
3. Remove from a fixing element of a nave a lock ring of fastening of the bearing.
4. Establish a fixing element of a nave on a table of a hydraulic press and, using a tubular opravka of the corresponding diameter, squeeze out the bearing from a fixing element of a nave.
5. Clear a nest for the bearing in a fixing element of a nave and, using an emery paper, remove all agnails. Check a condition of a lock ring of the bearing and, if necessary, replace it.
6. Apply a thin film engine oil on an external ring of the bearing.
7. Establish the bearing on a fixing element of a nave and, using the tubular opravka leaning on an external ring of the bearing, press the bearing in a nest against the stop.
8. Fix the bearing a lock ring. Thus check that the lock ring was accurately established in a flute of a fixing element of a nave.
9. Establish an internal ring of the bearing on an opravka of the corresponding diameter and press in the bearing a nave.
10. Check smoothness of rotation of the bearing, then establish a fixing element of a back nave on the car.