Mercedes W124

since 1985-1995 of release

Repair and car operation

W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
- SUSPENSION BRACKET
   23.2. General information
   23.3. Bearing of a forward nave
   23.4. Nave of a forward wheel
   23.5. Rotary fist
   23.6. Shock-absorber of a forward suspension bracket
   23.7. Spring of a forward suspension bracket
   23.8. Bottom lever of a forward suspension bracket
   23.9. Forward stabilizer of cross-section stability
   23.10. Fixing element of a back nave
   23.11. Replacement of the bearing of a back nave
   + 23.12. Shock-absorber of a back suspension bracket
   23.13. Spring of a back suspension bracket
   + 23.14. Levers of a back suspension bracket
   23.15. Bottom lever of a back suspension bracket
   23.16. Stabilizer of cross-section stability of a back suspension bracket
   23.17. Connecting earring of the stabilizer of cross-section stability
   23.18. System of a being self-leveled back suspension bracket on the Versatile person models
   + 23.19. Elements of a being self-leveled back suspension bracket
   23.20. Steering wheel
   23.21. Steering column
   23.22. Lock steering column / lock of ignition
   23.23. Contact group of the lock of ignition
   23.24. Rubber coupling of a steering shaft
   23.25. Steering transfer
   23.26. Soshka of steering transfer
   23.27. Replacement of the bottom sealing ring of steering transfer
   23.28. Pump of the amplifier of a steering
   23.29. Pumping of system of the amplifier of a steering
   23.30. Steering shock-absorber
   23.31. Central steering draft
   23.32. Intermediate lever of a steering
   23.34. Spherical hinges of cross-section steering draft
   23.35. Cross-section steering draft
   23.36. Corners of installation of wheels
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS

23.22. Lock steering column / lock of ignition

Lock cylinder

Removal

Removal of a decorative overlay of the lock of ignition

The tool which is necessary for making for removal of the cylinder of the lock of ignition (the sizes in millimeters)

Extraction of the cylinder of the lock of ignition

After installation of the special adaptation, having pulled for a key, take the cylinder of the lock of ignition.

Extraction of the cylinder of the lock of ignition from the case

PERFORMANCE ORDER

1. Using an edge of a small screw-driver, being careful, remove a decorative overlay of the lock of ignition (see fig. Removal of a decorative overlay of the lock of ignition).

2. Insert a key into the lock of ignition and turn it in situation 1.

3. Take a piece of a steel rigid wire in diameter of 2 mm and bend a wire in the form of a letter P, then from the inside grind off wire end faces at an angle 70 ° (see fig. The tool which is necessary for making for removal of the cylinder of the lock of ignition).

4. Insert a wire into the grooves located from two parties of the cylinder of the lock of ignition and press on a wire to compress clamps of the cylinder of the lock of ignition.

5. For a key take the ignition lock from a nest (see fig. Extraction of the cylinder of the lock of ignition).

6. Remove the adaptation from a wire, take the ignition key from the lock cylinder, then take the cylinder of the lock of ignition from the case (see fig. Extraction of the cylinder of the lock of ignition from the case).

Installation

PERFORMANCE ORDER

1. Insert the cylinder of the lock of ignition into the case of the lock of a steering column.

2. Establish the case on the cylinder of the lock of ignition so that dredging on the case was directed to a steering column.

3. Insert the ignition key, turn it in situation 1 and with small effort press the cylinder of the lock of ignition together with the case into the case of the lock of a steering column.

Prevention

At installation, the edge of the lock of ignition with teeths should be directed on a case label.

4. Check operation of the lock of ignition, then establish a decorative slip.

Ignition lock

Removal

Unscrewing of the nut, fixing a special rope to the ignition lock on models with an automatic transmission

Weakening of a bolt of fastening of the lock of ignition to a steering column

Pressing of the fixing pin, ignition fixing the lock

Removal of the lock of ignition from a steering column

PERFORMANCE ORDER

1. Remove a weight wire from the accumulator.

2. Remove the cylinder of the lock of ignition.

3. Remove the bottom furnish of the dashboard from the driver.

4. Note situation and disconnect the electric socket from the ignition lock.

5. On models with diesel engines mark vacuum hoses and disconnect them from the ignition lock. On models with an automatic transmission unscrew a special rope from the ignition lock (see fig. Unscrewing of the nut, fixing a special rope to the ignition lock on models with an automatic transmission).

6. Weaken a bolt of fastening of the lock of ignition, then press fixing pin and remove the ignition lock from a steering column (see fig. Weakening of a bolt of fastening of the lock of ignition to a steering column, Pressing of the fixing pin, ignition fixing the lock, Removal of the lock of ignition from a steering column).

Installation

PERFORMANCE ORDER

1. Installation is made in sequence, return to removal taking into account the next moments:
and – at removal of the lock of ignition the key in the lock of ignition should be in situation 1 constantly,
b–at installation of the lock of ignition check that the fixing pin was established in an opening of a steering column then tighten a bolt of fastening,
with – check correctness of an arrangement and fastening of electric conducting,
d–on models with diesel engines check correctness of connection of vacuum hoses to the lock of ignition,
е–check correctness of operation of the lock of ignition.