Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
- SUSPENSION BRACKET
   23.2. General information
   23.3. Bearing of a forward nave
   23.4. Nave of a forward wheel
   23.5. Rotary fist
   23.6. Shock-absorber of a forward suspension bracket
   23.7. Spring of a forward suspension bracket
   23.8. Bottom lever of a forward suspension bracket
   23.9. Forward stabilizer of cross-section stability
   23.10. Fixing element of a back nave
   23.11. Replacement of the bearing of a back nave
   + 23.12. Shock-absorber of a back suspension bracket
   23.13. Spring of a back suspension bracket
   + 23.14. Levers of a back suspension bracket
   23.15. Bottom lever of a back suspension bracket
   23.16. Stabilizer of cross-section stability of a back suspension bracket
   23.17. Connecting earring of the stabilizer of cross-section stability
   23.18. System of a being self-leveled back suspension bracket on the Versatile person models
   + 23.19. Elements of a being self-leveled back suspension bracket
   23.20. Steering wheel
   23.21. Steering column
   23.22. Lock steering column / lock of ignition
   23.23. Contact group of the lock of ignition
   23.24. Rubber coupling of a steering shaft
   23.25. Steering transfer
   23.26. Soshka of steering transfer
   23.27. Replacement of the bottom sealing ring of steering transfer
   23.28. Pump of the amplifier of a steering
   23.29. Pumping of system of the amplifier of a steering
   23.30. Steering shock-absorber
   23.31. Central steering draft
   23.32. Intermediate lever of a steering
   23.34. Spherical hinges of cross-section steering draft
   23.35. Cross-section steering draft
   23.36. Corners of installation of wheels
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






23.25. Steering transfer

GENERAL INFORMATION

Prevention

At installation of steering transfer it is necessary to use new bolts of fastening of the steering transfer, new nuts of spherical hinges, the central steering draft and cross-section steering draft, and also new bolts of fastening of the rubber coupling.


Removal

Steering transfer with the amplifier of a steering
1–steering transfer;
2–steering column;
3–central steering draft;
4–cross-section steering draft;
5–submitting and returnable hoses;
6–bolts

Places of connection of hoses to steering transfer

PERFORMANCE ORDER
1. Tighten the parking brake, then lift a forward part of the car and fix on supports.
2. Establish forward wheels in the provision of rectilinear movement and in this situation block a steering column the lock of a steering column.
Prevention

After removal of steering transfer do not rotate a steering wheel.


3. On models with the amplifier of a steering, using clips, press submitting and returnable hoses about steering transfer. Mark hoses, then unscrew connecting nuts and disconnect submitting and returnable hoses from steering transfer (see fig. Steering transfer with the amplifier of a steering, the Place of connection of hoses to steering transfer). Close jams the ends of hoses and an opening in steering transfer.
4. Using paint, note the mutual provision of the bottom end of a steering column, the rubber coupling and a shaft of a gear wheel of steering transfer. On some models for access to the rubber coupling it is necessary to remove the thermofilter from steering transfer.
5. Unscrew bolts of fastening of the rubber coupling and move it on a steering column so that she acted in film from a shaft of a gear wheel of steering transfer.
6. Unscrew the nuts, fixing spherical hinges of cross-section steering draft and the central steering bent for to a soshka of steering transfer. Using a stripper, remove spherical hinges of steering drafts from a soshka of steering transfer.
7. Unscrew three bolts, fixing steering transfer and the wheels located under an arch, and remove steering transfer from the car.

Repair

PERFORMANCE ORDER
1. Check a condition of steering transfer on existence of wear and damages. Repair of steering transfer is necessary for making at service station. It is independently possible to replace only a sealing ring of steering transfer.

Installation

Centering of a gear wheel of steering transfer on early models (till 1990)
1–steering transfer;
2–piston;
3–gear wheel;
4–blocking screw

Label combination on a gear wheel of steering transfer with a label on the case of steering transfer on models since 1990

PERFORMANCE ORDER
1. Before installation of new steering transfer it is necessary to center a steering gear wheel.
2. On early models (till 1990) unscrew a cap and the sealing ring located sideways of the block of steering transfer. Then turn a gear wheel in such situation that the centering opening was combined with cap dredging. In the presence of the konusny screw of blocking, screw in it so that it is reliable to block a gear wheel of steering transfer (see fig. A centering of a gear wheel of steering transfer on early models (till 1990)).
3. On later models (since 1990) combine an adjusting label on a gear wheel of steering transfer with a label on the case of steering transfer (see fig. Label combination on a gear wheel of steering transfer with a label on the case of steering transfer on models since 1990).
4. Establish steering transfer into place. Combine the labels put before removal (at repeated installation of steering transfer) or check correctness of installation of a gear wheel (at installation of new steering transfer) and, moving the rubber coupling to a steering column, connect it to shaft of a gear wheel of steering transfer.
5. Fix steering transfer by new bolts, having tightened them the demanded moment.
6. On early models unscrew the konusny bolt fixing a gear wheel, and establish into place a cap and a sealing ring.
7. Fix the rubber coupling new bolts, having tightened them the demanded moment.
8. Insert pins of spherical hinges of the central and cross-section steering drafts into a soshka of the steering mechanism and fix them new nuts, having tightened them the demanded moment.
9. On models with the amplifier of a steering connect hoses to steering transfer and fix them connecting nuts, having tightened them the demanded moment. Remove air from hydraulic system of the amplifier of a steering.