Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
- SUSPENSION BRACKET
   23.2. General information
   23.3. Bearing of a forward nave
   23.4. Nave of a forward wheel
   23.5. Rotary fist
   23.6. Shock-absorber of a forward suspension bracket
   23.7. Spring of a forward suspension bracket
   23.8. Bottom lever of a forward suspension bracket
   23.9. Forward stabilizer of cross-section stability
   23.10. Fixing element of a back nave
   23.11. Replacement of the bearing of a back nave
   + 23.12. Shock-absorber of a back suspension bracket
   23.13. Spring of a back suspension bracket
   + 23.14. Levers of a back suspension bracket
   23.15. Bottom lever of a back suspension bracket
   23.16. Stabilizer of cross-section stability of a back suspension bracket
   23.17. Connecting earring of the stabilizer of cross-section stability
   23.18. System of a being self-leveled back suspension bracket on the Versatile person models
   + 23.19. Elements of a being self-leveled back suspension bracket
   23.20. Steering wheel
   23.21. Steering column
   23.22. Lock steering column / lock of ignition
   23.23. Contact group of the lock of ignition
   23.24. Rubber coupling of a steering shaft
   23.25. Steering transfer
   23.26. Soshka of steering transfer
   23.27. Replacement of the bottom sealing ring of steering transfer
   23.28. Pump of the amplifier of a steering
   23.29. Pumping of system of the amplifier of a steering
   23.30. Steering shock-absorber
   23.31. Central steering draft
   23.32. Intermediate lever of a steering
   23.34. Spherical hinges of cross-section steering draft
   23.35. Cross-section steering draft
   23.36. Corners of installation of wheels
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






23.26. Soshka of steering transfer

GENERAL INFORMATION

Prevention

At installation it is necessary to use new nuts of fastening of spherical hinges, the central and cross-section steering drafts and a new nut of a tightening bolt of a steering soshka.


Removal

Arrangement of a bolt (1) and a lock ring (2) fastenings of a soshka to steering transfer


PERFORMANCE ORDER
1. Tighten the parking brake, then lift a forward part of the car and fix on supports.
2. Unscrew the nuts, fixing pins of spherical hinges of the central and cross-section steering bent for to a soshka of steering transfer. Using a stripper of spherical hinges, take pins of spherical hinges from a soshka of steering transfer.
3. Unscrew a nut and take tightening a bolt, fixing a soshka to steering transfer, then remove a lock ring (see drawing).
4. Measure and write down distance between the upper edge of a soshka and a case of steering transfer. Check that the combination label on a shaft is visible through tightening a soshka cut. Otherwise put a label.
5. Using a stripper, remove a soshka from a shaft of steering transfer. Check a condition of the bottom sealing ring of steering transfer and, if necessary, replace it.

Installation

PERFORMANCE ORDER
1. Clear shlitsa of a shaft of steering transfer and a soshka.
2. Put on a shlitsa of a soshka blocking structure of Loctite 270.
3. Establish a soshka on a shlitsa of a shaft of steering transfer. Thus the combination label on a shaft should be visible through a tightening crack of a soshka.
4. Move a soshka on a shaft so that the distance between the top part of a soshka and a case of steering transfer was equal to the earlier measured.
5. Insert tightening a soshka bolt, then screw on it a new nut and tighten the demanded moment. Establish a lock ring in a shaft flute.
6. Establish pins of spherical hinges of steering drafts in a soshka, screw on them new nuts and tighten them the demanded moment. Lower the car.