W124 Mercedes + Governing bodies and control devices + MAINTENANCE + 2. Maintenance (diesel engines) + ENGINE + 4. Repair of 6-cylinder petrol SOHC engines + 5. Repair of 6-cylinder petrol DOHC engines + 6. Repair of the diesel engine established in the car + 7. Major maintenance of engines + COOLING SYSTEM + FUEL SYSTEM + 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC) + 11. System of injection of BOSCH HFM fuel + 12. Fuel system of diesel engines + 13. Fuel system of diesel engines + SYSTEMS OF START, IGNITION + 15. System of ignition of 4-cylinder petrol engines + 16. System of ignition of four-cylinder petrol engines + PRESTARTING HEATING + TRANSMISSION + 19. Mechanical transmission + 20. Automatic transmission + POWER SHAFTS + BRAKE SYSTEM - SUSPENSION BRACKET 23.2. General information 23.3. Bearing of a forward nave 23.4. Nave of a forward wheel 23.5. Rotary fist 23.6. Shock-absorber of a forward suspension bracket 23.7. Spring of a forward suspension bracket 23.8. Bottom lever of a forward suspension bracket 23.9. Forward stabilizer of cross-section stability 23.10. Fixing element of a back nave 23.11. Replacement of the bearing of a back nave + 23.12. Shock-absorber of a back suspension bracket 23.13. Spring of a back suspension bracket + 23.14. Levers of a back suspension bracket 23.15. Bottom lever of a back suspension bracket 23.16. Stabilizer of cross-section stability of a back suspension bracket 23.17. Connecting earring of the stabilizer of cross-section stability 23.18. System of a being self-leveled back suspension bracket on the Versatile person models + 23.19. Elements of a being self-leveled back suspension bracket 23.20. Steering wheel 23.21. Steering column 23.22. Lock steering column / lock of ignition 23.23. Contact group of the lock of ignition 23.24. Rubber coupling of a steering shaft 23.25. Steering transfer 23.26. Soshka of steering transfer 23.27. Replacement of the bottom sealing ring of steering transfer 23.28. Pump of the amplifier of a steering 23.29. Pumping of system of the amplifier of a steering 23.30. Steering shock-absorber 23.31. Central steering draft 23.32. Intermediate lever of a steering 23.34. Spherical hinges of cross-section steering draft 23.35. Cross-section steering draft 23.36. Corners of installation of wheels + BODY + ELECTRIC EQUIPMENT + CHECK OF MALFUNCTIONS
|
Prevention
The bearing of a nave of a forward wheel is pressed in a rotary fist therefore at removal there is a high probability of its damage and, probably, its replacement is required.
Nave of a forward wheel
Removal
Screw-driver use for removal of a protective cap from a nave of a forward wheel
Removal of a spring from a nave axis
Weakening of the tightening bolt, fixing a nut of a nave of a forward wheel
Unscrewing of a nut of fastening of a nave of a forward wheel
PERFORMANCE ORDER |
1. Remove a forward brake disk. On models with anti-blocking system remove the ABS sensor from a forward wheel. |
2. Using a screw-driver or a drift, remove the protective cap located in the center of a nave of a forward wheel. At damage of a protective cap at removal it is necessary to replace it (see fig. Screw-driver use for removal of a protective cap from a nave of a forward wheel). |
3. At existence remove a spring from a nave axis (see fig. Removal of a spring from a nave axis). |
4. Weaken tightening a bolt fixing a nut of fastening of a nave from unscrewing, then unscrew a nut and remove it from a nave axis. At existence remove a persistent washer (see fig. Weakening of the tightening bolt, fixing a nut of a nave of a forward wheel, Unscrewing of a nut of fastening of a nave of a forward wheel). |
5. Remove a nave of a forward wheel from a rotary fist. If the nave does not act in film, it is necessary to use a stripper. |
6. If the internal ring of the bearing remained on a rotary fist, using a stripper, remove it from a nave axis, then remove a sealing ring of a nave. |
7. Check a condition of a pin of a rotary fist and, if necessary, replace. |
|
Repair
PERFORMANCE ORDER |
1. Take from a nave an internal ring of the external bearing. |
2. From a back part of naves remove a sealing ring and then take an internal ring of the internal bearing. |
3. Establish a nave on the corresponding opravka and, using a hammer and a drift, beat out an internal ring of the external bearing. Thus do not warp a ring not to damage a bearing nest in a nave. |
4. Overturn a nave and similarly beat out an external ring of the internal bearing. |
5. Clear a nave of dirt and greasing and, using an emery paper, polish agnails on a nave. Check a nave condition on existence of cracks, wear and mechanical damages and, if necessary, replace. On models with anti-blocking system check a condition of a gear rotor of the sensor. |
6. Before assembly apply a thin film greasings on an external ring of the bearing and an interfaced surface of a nave. Also grease racetracks of an internal ring. |
7. Establish a nave on an opravka and establish an external ring of the internal bearing in a nave. Using the tubular opravka leaning on an external ring of the bearing, and a press, press a bearing ring in a nave against the stop. At a press fitting do not warp a bearing ring. |
8. Overturn a nave and similarly press in a nave an external ring of the external bearing. |
9. Establish an internal ring of the internal bearing. On a back part of a nave establish a sealing ring working edges to the bearing. Fill bearings with the greasing making two thirds of full volume of greasing, then establish an internal ring of the external bearing. |
|
Installation
PERFORMANCE ORDER |
1. Apply a thin film greasings on a back part of a sealing ring of a nave and establish a nave on a pin of a rotary fist. |
2. Establish a persistent washer and screw a nut of fastening of a nave. |
3. Screwing up a nut of fastening of a nave, press internal rings of the bearing of a nave on a pin of a rotary fist. After installation of a nave adjust axial люфт the nave bearing. After carrying out adjustment tighten tightening a bolt fixing a nut of fastening of a nave from unscrewing. |
4. Establish a spring on a pin of a rotary fist. |
5. Establish on a nave a protective cap with greasing. |
6. Establish a brake disk and, at existence, the sensor of a forward wheel of anti-blocking system of brakes. |
|
|
|