W124 Mercedes + Governing bodies and control devices + MAINTENANCE + 2. Maintenance (diesel engines) + ENGINE + 4. Repair of 6-cylinder petrol SOHC engines + 5. Repair of 6-cylinder petrol DOHC engines + 6. Repair of the diesel engine established in the car + 7. Major maintenance of engines + COOLING SYSTEM + FUEL SYSTEM + 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC) + 11. System of injection of BOSCH HFM fuel + 12. Fuel system of diesel engines + 13. Fuel system of diesel engines + SYSTEMS OF START, IGNITION + 15. System of ignition of 4-cylinder petrol engines + 16. System of ignition of four-cylinder petrol engines + PRESTARTING HEATING + TRANSMISSION + 19. Mechanical transmission + 20. Automatic transmission + POWER SHAFTS + BRAKE SYSTEM - SUSPENSION BRACKET 23.2. General information 23.3. Bearing of a forward nave 23.4. Nave of a forward wheel 23.5. Rotary fist 23.6. Shock-absorber of a forward suspension bracket 23.7. Spring of a forward suspension bracket 23.8. Bottom lever of a forward suspension bracket 23.9. Forward stabilizer of cross-section stability 23.10. Fixing element of a back nave 23.11. Replacement of the bearing of a back nave + 23.12. Shock-absorber of a back suspension bracket 23.13. Spring of a back suspension bracket + 23.14. Levers of a back suspension bracket 23.15. Bottom lever of a back suspension bracket 23.16. Stabilizer of cross-section stability of a back suspension bracket 23.17. Connecting earring of the stabilizer of cross-section stability 23.18. System of a being self-leveled back suspension bracket on the Versatile person models + 23.19. Elements of a being self-leveled back suspension bracket 23.20. Steering wheel 23.21. Steering column 23.22. Lock steering column / lock of ignition 23.23. Contact group of the lock of ignition 23.24. Rubber coupling of a steering shaft 23.25. Steering transfer 23.26. Soshka of steering transfer 23.27. Replacement of the bottom sealing ring of steering transfer 23.28. Pump of the amplifier of a steering 23.29. Pumping of system of the amplifier of a steering 23.30. Steering shock-absorber 23.31. Central steering draft 23.32. Intermediate lever of a steering 23.34. Spherical hinges of cross-section steering draft 23.35. Cross-section steering draft 23.36. Corners of installation of wheels + BODY + ELECTRIC EQUIPMENT + CHECK OF MALFUNCTIONS
|
Removal
Unscrewing of nuts from sharnirny bolts of fastening of the bottom lever of a forward suspension bracket
PERFORMANCE ORDER |
1. Tighten the hand brake, then lift a forward part of the car and fix on supports. Remove the corresponding forward wheel. |
2. Unscrew screws and remove an engine mudguard from the lower part of a motor compartment. |
3. Unscrew the nuts, fixing a collar of the stabilizer of cross-section stability to a forward part of the bottom lever of a forward suspension bracket and remove from the stabilizer a rubber pillow. |
4. Using the special adaptation for compression of springs, compress a spring so that it departed from the top fastening. When using the special adaptation for compression of springs watch, that rounds of a spring were reliably grasped, and compression of a spring make from the opposite sides. |
5. A jack through wooden whetstone support the bottom lever of a forward suspension bracket. |
6. Unscrew a nut and take tightening a bolt, fixing a pin of the spherical hinge of the bottom lever of a forward suspension bracket to a rotary fist. Being careful, lower the bottom lever, taking a pin of the spherical hinge from a clip of a rotary fist so that it was possible to remove a cylindrical spring from a basic cup. |
7. Using paint, note the provision of ekstsentrikovy washers of sharnirny bolts of fastening of the bottom lever to the bottom frame. It is necessary for installation of the bottom lever in a starting position for preservation of corners of disorder and a convergence of forward wheels. |
8. Unscrew nuts of fastening of sharnirny bolts of the bottom lever both take bolts and remove ekstsentrikovy washers (see drawing). |
9. Take the bottom lever of a forward suspension bracket from under the car. |
|
Repair
PERFORMANCE ORDER |
1. Clear the bottom lever of a forward suspension bracket of dirt and check its condition on existence of cracks, deformation or mechanical damages. Special attention turn on a condition of plugs of fastening of the lever and the spherical hinge. If plugs or the spherical hinge of the bottom lever are subject to replacement, replacement is necessary for making in a specialized workshop as use of a hydraulic press and special opravka for this purpose is necessary. |
2. Check a condition of a protective cover of the spherical hinge of the bottom lever on existence of gaps, cracks or aging and, if necessary, replace. |
|
Installation
PERFORMANCE ORDER |
1. Establish the bottom lever of a forward suspension bracket on a place and insert forward and back sharnirny bolts with ekstsentrikovy washers. A forward sharnirny bolt establish from the back party of the car, and a back bolt - from the forward party of the car. Establish ekstsentrikovy washers in situation in which they were before removal. Screw new nuts on sharnirny bolts, but do not tighten them finally. |
2. Check that the bottom basic plate of a spring pure, then establish the top basic plate on a spring and establish a spring with the top plate into place. |
3. Turn a cylindrical spring so that its bottom end correctly settled down in the bottom nest of a spring. Establish the top basic plate of a spring under fastening and, being careful, lift the bottom lever of a forward suspension bracket, thus at the same time level a pin of the spherical hinge with an opening of a rotary fist. |
4. Check correctness of placement of a spring, then insert tightening a bolt of fastening of a pin of the spherical hinge to a rotary fist. Screw on tightening a bolt a new nut and tighten it the demanded moment. For prevention of corrosion fill with hermetic a crack of a clip of a pin of the spherical hinge in a rotary fist. |
5. Establish a rubber pillow on the stabilizer of cross-section stability, establish it on the bottom lever, then establish a collar of fastening and screw in new bolts, having tightened them the demanded moment. |
6. Take a jack from under the bottom lever of a forward suspension bracket, then remove from a cylindrical spring the adaptation for compression of springs. Check correctness of an arrangement of the ends of a spring. |
7. Establish a wheel, then lower the car on the earth and tighten bolts of fastening of a wheel the demanded moment. |
8. Shake the car for the correct installation of the bottom lever of a forward suspension bracket. |
9. Check that ekstsentrikovy washers of sharnirny bolts of fastening of the bottom lever are established according to the labels put earlier, and tighten nuts of fastening of sharnirny bolts the demanded moment. |
|
|
|