Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
- BODY
   24.2. General information
   24.3. Care of a body
   24.4. Care of an upholstery and rugs
   24.5. Repair of insignificant damages of a body
   24.6. Repair of strong damages of a body
   24.7. Front bumper
   24.8. Rear bumper
   24.9. Cowl
   24.10. Cable of opening of the lock of a cowl
   24.11. Cowl lock
   24.12. Doors
   24.13. Door upholstery
   - 24.14. Door handles and locks
      24.14.2. Installation
   + 24.15. Glass of a door and window regulators
   24.16. Trunk lid
   24.17. Trunk lid lock
   24.18. Back door
   24.19. Lock of a back door
   24.20. Elements of the central lock
   24.21. External rear-view mirrors
   24.22. Wind and back flew down
   24.23. Hatch
   24.24. External details of a body
   24.25. Sitting
   24.25.2. Installation
   24.26. Mechanism of a tension of a seat belt of forward sitting
   + 24.27. Seat belt elements
   24.28. Interior furnish
   24.29. Central console
   24.30. Dashboard
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






24.14.2. Installation

Internal handle of opening of a door

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

Cylinder of the lock of a forward door

PERFORMANCE ORDER
1. Insert the lock cylinder into a casing, then establish draft and a spring and fix them a fixing pin. Check operation of the cylinder of the lock.
2. Check correctness of an arrangement of consolidation, then insert a casing of the cylinder of the lock into place, combining draft of the cylinder of the lock with the door lock. Check correctness of a relative positioning of the lock and the lock cylinder, then screw in the screw of fastening of the cylinder of the lock and establish at a door end face a cap.

External handle of opening of a forward door

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal. Check correctness of an arrangement of laying of the handle on a door. Check correctness of combination of the lever of the handle with draft of the lock, then establish the lock cylinder. Check operation of the lock and the handle. Establish on a door a protective film and a door upholstery.

Lock of a forward door

Cap removal for gap adjustment between draft of the lock and the lever of the external handle

Rotation of the ekstsentrikovy screw for gap adjustment between draft of the lock and the lever of the external handle

PERFORMANCE ORDER
1. At existence, connect the electric socket to the lock, then put the lock into place. Thus the lever of the lock should be established behind the handle lever. Screw in screws of fastening of the lock and tighten them the demanded moment.
2. Establish the lock cylinder.
3. Check a gap between draft of the lock and the lever of the external handle. The gap should be in limits of 0-1 mm. For adjustment of size of a gap remove a cap from an end face of a door and, rotating the ekstsentrikovy screw, adjust a gap (see fig. Cap removal for gap adjustment between draft of the lock and the lever of the external handle, Rotation of the ekstsentrikovy screw for gap adjustment between draft of the lock and the lever of the external handle). After adjustment of a gap establish a cap into place.
4. Connect bent for to the lock and fix it in directing on doors. On models with the central lock establish the executive mechanism.
5. Check operation of the lock, then establish on a door a protective film and a door upholstery.

External handle of opening of a back door

PERFORMANCE ORDER
1. Establish on a door a handle arm, screw in screws of fastening and tighten them the demanded moment.
2. Establish laying and the handle on a door. Thus the lever of the handle should be combined with draft of the lock.
3. Establish an emphasis of the handle and fix it the screw, then establish into place door consolidation.
4. Check operation of the lock of a back door, then establish on a door a protective film and a door upholstery.

Lock of a back door

PERFORMANCE ORDER
1. Put the lock of a back door on a place and fix screws, having tightened them the demanded moment.
2. Connect to the lock of draft and fix them in directing on doors.
3. Establish the external handle of a back door and check operation of the lock. Establish on a door a protective film and a door upholstery.