Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
- BODY
   24.2. General information
   24.3. Care of a body
   24.4. Care of an upholstery and rugs
   24.5. Repair of insignificant damages of a body
   24.6. Repair of strong damages of a body
   24.7. Front bumper
   24.8. Rear bumper
   24.9. Cowl
   24.10. Cable of opening of the lock of a cowl
   24.11. Cowl lock
   24.12. Doors
   24.13. Door upholstery
   + 24.14. Door handles and locks
   - 24.15. Glass of a door and window regulators
      24.15.2. Installation
   24.16. Trunk lid
   24.17. Trunk lid lock
   24.18. Back door
   24.19. Lock of a back door
   24.20. Elements of the central lock
   24.21. External rear-view mirrors
   24.22. Wind and back flew down
   24.23. Hatch
   24.24. External details of a body
   24.25. Sitting
   24.25.2. Installation
   24.26. Mechanism of a tension of a seat belt of forward sitting
   + 24.27. Seat belt elements
   24.28. Interior furnish
   24.29. Central console
   24.30. Dashboard
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






24.15. Glass of a door and window regulators

24.15.1. Removal

GENERAL INFORMATION

Removal of a protective film from the interior of a door

PERFORMANCE ORDER
1. Remove a door upholstery.
2. Being careful, remove from the interior of a door a protective film (see fig. Removal of a protective film from the interior of a door). If at removal the protective film is damaged, replace it.

Forward door on the Sedan models and the Versatile person

Unscrewing of the nut, fixing the window regulator lever to directing glasses

Detachment of glass of a door from ползуна directing and back ползуна a window regulator

PERFORMANCE ORDER
1. Lower glass down to an emphasis so that the nut of fastening directing a window regulator was available through an aperture from the interior of a door, then remove a weight wire from the accumulator.
2. Unscrew a nut, fixing the window regulator lever to directing glasses (see fig. Unscrewing of the nut, fixing the window regulator lever to directing glasses).
3. Remove the forward lever of a window regulator with directing glasses, then lift a back part of glass and disconnect glass from ползуна directing and back ползуна a window regulator (see fig. A detachment of glass of a door from ползуна directing and back ползуна a window regulator).
4. Being careful, lift glass and take it up from a door window. If necessary, remove ползун from the lower part directing glasses.

Forward door on Compartment models

PERFORMANCE ORDER
1. Lower glass down to an emphasis so that the nut of fastening directing a window regulator was available through an aperture from the interior of a door, then remove a weight wire from the accumulator.
2. Unscrew a nut, fixing the window regulator lever to directing glasses (see fig. Unscrewing of the nut, fixing the window regulator lever to directing glasses).
3. Unscrew above and below screws of fastening of a lobby directing glasses and take it from a door.
4. Weaken nuts of fastening of the holder of glass to directing, then remove glass from a window regulator and take it up through a door window.

Window regulator of a forward door on the Sedan models and the Versatile person

Unscrewing of screws of fastening of electroconducting to the window regulator engine

Arrangement of nuts of fastening of a window regulator

Window regulator extraction through an aperture from the interior of a door

PERFORMANCE ORDER
1. Lower glass down to an emphasis so that the nut of fastening directing a window regulator was available through an aperture from the interior of a door, then remove a weight wire from the accumulator.
2. Unscrew a nut, fixing the window regulator lever to directing glasses (see fig. Unscrewing of the nut, fixing the window regulator lever to directing glasses).
3. Remove the forward lever of a window regulator with directing glasses, then lift a back part of glass and disconnect glass from ползуна directing and back ползуна a window regulator (see fig. A detachment of glass of a door from ползуна directing and back ползуна a window regulator).
4. Lift glass against the stop up, then, using a sticky tape, fix glass in this situation on a door.
5. On models with electric window regulators note an arrangement of each wire, then unscrew screws and disconnect wires from the window regulator engine (see fig. Unscrewing of screws of fastening of electroconducting to the window regulator engine).
6. Unscrew nuts and the bolts, fixing a window regulator and take a window regulator through an aperture of an internal part of a door, having thus released top ползун from directing to doors (see fig. An arrangement of nuts of fastening of a window regulator, window regulator Extraction through an aperture from the interior of a door).

Window regulator of a forward door on Compartment models


Prevention

At installation of a window regulator it is necessary to use the zaklepochny gun and new rivets.


PERFORMANCE ORDER
1. Lower glass down to an emphasis so that the nut of fastening directing a window regulator was available through an aperture from the interior of a door, then remove a weight wire from the accumulator.
2. Unscrew a nut, fixing the window regulator lever to directing glasses (see fig. Unscrewing of the nut, fixing the window regulator lever to directing glasses).
3. On models with electric window regulators note an arrangement of each wire, then unscrew screws and disconnect wires from the window regulator engine.
4. Unscrew nuts of fastening directing, then remove glass from a window regulator and take it up through a frame of a window of a door.
5. Using a marker, note an arrangement of nuts of fastening of the lever of a window regulator on a door, then unscrew nuts.
6. Using a drill in diameter of 6 mm, being careful, drill rivets of fastening of a window regulator to a door.
7. Take a window regulator through an aperture from the interior of a door.

Back door on the Sedan models and the Versatile person

Removal of a sealant of glass from a frame of a window of a door

Unscrewing of the top screw of fastening back directing glasses

Unscrewing of the bottom bolt of fastening back directing glasses

Removal back directing glasses from a door

Detachment directing glasses from a window regulator

Removal of glass of a back door through a frame of a window of a door

PERFORMANCE ORDER
1. Lower glass so that the directing was available through an aperture from the interior of a door, then remove a weight wire from the accumulator.
2. Being careful, remove a sealant of glass and take it from a frame of a window of a door (see fig. Removal of a sealant of glass from a frame of a window of a door).
3. Unscrew a bolt located in the lower part and the screw, located in the top part of fastening of a directing back part of glass. Move directing down and take it from a door (see fig. Unscrewing of the top screw of fastening back directing glasses, Unscrewing of the bottom bolt of fastening back directing glasses,Removal back directing glasses from a door ).
4. Turn glass and disconnect directing glasses from a window regulator, then lift glass up and take it from a frame of a window of a door (see fig. A detachment directing glasses from a window regulator, Removal of glass of a back door through a frame of a window of a door).

Back lateral glass on Compartment models

PERFORMANCE ORDER
1. Remove an inertial drum of a seat belt of a forward seat.
2. Remove from a body the top consolidation of glass.
3. Being careful, remove a protective film from a body for access to a window regulator and glass. At damage of a protective film it is necessary to replace it.
4. Lower glass in such situation that nuts of fastening of glass to a window regulator were available through doorways.
5. Unscrew nuts of fastening of glass to a window regulator and remove glass from the car.

Window regulators of a back door on the Sedan models and the Versatile person

Unscrewing of screws of fastening of electroconducting to the window regulator engine

Arrangement of nuts and bolt of fastening of a window regulator to a door

Window regulator extraction through an aperture from the interior of a door

PERFORMANCE ORDER
1. Lower glass in such situation that access to directing glasses was possible through a doorway, then remove a weight wire from the accumulator.
2. Incline glass at doors and remove directing glasses from the window regulator lever. Lift glass against the stop up and, using a sticky tape, fix it in this situation.
3. On models with electric window regulators note an arrangement of each wire, then unscrew screws and remove wires from the window regulator engine (see fig. Unscrewing of screws of fastening of electroconducting to the window regulator engine).
4. Unscrew a bolt and nuts of fastening of a window regulator and take a window regulator through an aperture from the interior of a door (see fig. An arrangement of nuts and a bolt of fastening of a window regulator to a door, window regulator Extraction through an aperture from the interior of a door).

Window regulator of back lateral glass on Compartment models

PERFORMANCE ORDER
1. Remove back lateral glass from a body.
2. For access to a window regulator unscrew screws and remove from a body a basic plate.
3. Uncover a back part of the switch of a window regulator. Note an arrangement of each wire and disconnect wires of the engine of a window regulator from the switch. Take a plait of wires from fastening brackets so that it could be removed together with a window regulator.
4. Unscrew bolts and remove an assembly plate of an armrest from a body.
5. Being careful, remove a back part of a molding and a cap for access to nuts of fastening of a window regulator.
6. Unscrew nuts and remove a window regulator from the car.