Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
- BODY
   24.2. General information
   24.3. Care of a body
   24.4. Care of an upholstery and rugs
   24.5. Repair of insignificant damages of a body
   24.6. Repair of strong damages of a body
   24.7. Front bumper
   24.8. Rear bumper
   24.9. Cowl
   24.10. Cable of opening of the lock of a cowl
   24.11. Cowl lock
   24.12. Doors
   24.13. Door upholstery
   + 24.14. Door handles and locks
   + 24.15. Glass of a door and window regulators
   24.16. Trunk lid
   24.17. Trunk lid lock
   24.18. Back door
   24.19. Lock of a back door
   24.20. Elements of the central lock
   24.21. External rear-view mirrors
   24.22. Wind and back flew down
   24.23. Hatch
   24.24. External details of a body
   24.25. Sitting
   24.25.2. Installation
   24.26. Mechanism of a tension of a seat belt of forward sitting
   + 24.27. Seat belt elements
   24.28. Interior furnish
   24.29. Central console
   24.30. Dashboard
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






24.16. Trunk lid

Removal

Extraction of a percussion cap of fastening of internal furnish of a trunk lid

Removal of internal furnish of a trunk lid

Arrangement of bolts of fastening of hinges to a trunk lid

PERFORMANCE ORDER
1. Open a trunk lid and remove a weight wire from the accumulator.
2. Being careful, take percussion caps of fastening and remove internal furnish of a trunk lid (see fig. Extraction of a percussion cap of fastening of internal furnish of a trunk lid, Removal of internal furnish of a trunk lid).
3. Mark and disconnect electric sockets from the electric units located on a trunk lid. Adhere to electric sockets a thin long cord. Remove rubber sealing laying of a plait of wires and extend electroconducting from a trunk lid. After emergence of a cord from a trunk lid untie it from electric sockets and leave in a trunk lid. Further this cord is necessary for using for a tightening of wires in a trunk lid.
4. Using a marker or a pencil, note position of hinges on a trunk lid, then unscrew bolts of fastening of hinges and uncover a luggage carrier (see fig. An arrangement of bolts of fastening of hinges to a trunk lid). Note an arrangement and remove all laying located between hinges and a trunk lid.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal. Installation of hinges make according to earlier made labels.
2. For trunk lid installation aflush with other elements of a body weaken bolts of fastening of hinges of a trunk lid and adjust the provision of a trunk lid then tighten bolts.