W124 Mercedes + Governing bodies and control devices + MAINTENANCE + 2. Maintenance (diesel engines) + ENGINE + 4. Repair of 6-cylinder petrol SOHC engines + 5. Repair of 6-cylinder petrol DOHC engines + 6. Repair of the diesel engine established in the car + 7. Major maintenance of engines + COOLING SYSTEM + FUEL SYSTEM + 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC) + 11. System of injection of BOSCH HFM fuel + 12. Fuel system of diesel engines + 13. Fuel system of diesel engines + SYSTEMS OF START, IGNITION + 15. System of ignition of 4-cylinder petrol engines + 16. System of ignition of four-cylinder petrol engines + PRESTARTING HEATING + TRANSMISSION + 19. Mechanical transmission + 20. Automatic transmission + POWER SHAFTS + BRAKE SYSTEM + SUSPENSION BRACKET - BODY 24.2. General information 24.3. Care of a body 24.4. Care of an upholstery and rugs 24.5. Repair of insignificant damages of a body 24.6. Repair of strong damages of a body 24.7. Front bumper 24.8. Rear bumper 24.9. Cowl 24.10. Cable of opening of the lock of a cowl 24.11. Cowl lock 24.12. Doors 24.13. Door upholstery + 24.14. Door handles and locks + 24.15. Glass of a door and window regulators 24.16. Trunk lid 24.17. Trunk lid lock 24.18. Back door 24.19. Lock of a back door 24.20. Elements of the central lock 24.21. External rear-view mirrors 24.22. Wind and back flew down 24.23. Hatch 24.24. External details of a body 24.25. Sitting 24.25.2. Installation 24.26. Mechanism of a tension of a seat belt of forward sitting + 24.27. Seat belt elements 24.28. Interior furnish 24.29. Central console 24.30. Dashboard + ELECTRIC EQUIPMENT + CHECK OF MALFUNCTIONS
|
Removal
Arrangement of caps on cowl inside
Arrangement of bolts of fastening of hinges to a cowl
PERFORMANCE ORDER |
1. Open a cowl and enclose pure rags under cowl corners to protect a paint and varnish covering of the car at cowl removal. |
2. Being careful, remove the caps located in the central part of a cowl, for access to a hose of a washer and electric sockets. Disconnect submitting hose of a washer from the control valve and electric sockets. Adhere to a hose and the electric socket a thin long cord. Extend from a cowl electroconducting and a hose and untie from them a cord, leaving it in a cowl. Further the cord is required for a tightening in an electroconducting and hose cowl (see fig. An arrangement of caps on cowl inside). |
3. Using a marker, note position of hinges on a cowl (see fig. An arrangement of bolts of fastening of hinges to a cowl). |
4. Unscrew bolts of fastening of the left and right hinge of a cowl and, being careful, remove a cowl. |
5. Check a condition of hinges of a cowl on existence люфта and wear and, if necessary, replace them. Pay attention that for replacement of the hinge of a cowl it is necessary to remove a forward wing and it is desirable to carry out this work at service station. |
|
Installation and adjustment
PERFORMANCE ORDER |
1. Using two assistants, establish a cowl and screw in bolts of fastening of hinges of a cowl by hand. Level cowl hinges according to earlier made labels and tighten fastening bolts. |
2. Close a cowl and check its arrangement of rather adjacent surfaces. Adjust the provision of a cowl so that at the closed cowl the gap on perimeter of a cowl was identical from all directions. For adjustment weaken bolts of fastening of hinges of a cowl and, moving a cowl, adjust its situation. If this adjustment does not provide the demanded provision of a cowl, further adjustment can be made, having weakened nuts of fastening and having changed position of hinges of a cowl. Access to nuts of fastening of hinges of a cowl is possible after removal of protection of a wing. For adjustment of a forward part on height it is necessary to screw in or unscrew the rubber pillows located on a forward cross-piece. |
|
|
|