Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
- ENGINE
   3.2. General data
   3.3. Repair operations on the engine established in the car
   3.4. Check of pressure of compression
   3.5. Top dead point (VMT) of the piston of the first cylinder
   3.6. Cover of a head of the block of cylinders
   3.7. Pulley cranked shaft / quencher of krutilny fluctuations and nave
   + 3.8. Cover of a driving chain
   3.9. Check and replacement of a driving chain
   + 3.10. Mechanism of a tension of a driving chain, asterisk and uspokoitel of a chain
   3.11. Intermediate shaft
   + 3.12. Drive of valves, pushers and camshaft
   + 3.13. Head of the block of cylinders
   3.14. Oil pallet
   3.15. Oil pump
   3.16. Drive flywheel / plate
   3.17. Replacement of sealing rings of a cranked shaft
   3.18. Bearing replacement in an end face of a cranked shaft
   3.19. Check and replacement of a support of the power unit
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






3.14. Oil pallet

GENERAL INFORMATION

System of greasing of the engine
1–oil pallet;
2–щуп for measurement of level of engine oil;
3–cranked shaft;
4–maslozabornik;
5–internal rotor;
6–external rotor;
7–case of the oil pump;
8–safety valve;
9–mesh filter;
10-oil filter

Removal

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Remove the air filter.
3. Remove the bottom mudguard of the engine.
4. Remove the forward stabilizer of cross-section stability.
5. Merge from the engine engine oil.
6. At existence disconnect the electric socket from the sensor of level of the engine oil established in the oil pallet.
7. Remove a casing of the fan of a radiator and arrange it on a krylchatka of the fan.
8. Disconnect a reception exhaust pipe from an inlet collector.
9. Under the car unscrew nuts and remove an exhaust system from an arm on a transmission.
10. Unscrew two bottom bolts of fastening of a transmission to the engine.
11. Hook on the engine slings of the load-lifting mechanism and raise so that the weight of the engine was perceived by the load-lifting mechanism.
12. In turn from two parties of the car unscrew the bottom bolts of fastening of arms of support of the engine.
13. Raise the engine so to get access to bolts of fastening of the oil pallet.
14. Evenly and gradually unscrew bolts of fastening of the oil pallet. Thus note their arrangement as bolts have different length.
15. Remove the oil pallet from the car together with laying.

Installation

PERFORMANCE ORDER
1. Clear all traces of dirt and oil of interfaced surfaces of the oil pallet and the block of cylinders.
2. Establish new laying on the oil pallet. Screw up bolts of fastening of the oil pallet, working from the center in diagonal sequence.
3. Lower the engine and tighten the bottom bolts of fastening of arms of support of the engine.
4. Remove slings of the load-lifting mechanism from the engine.
5. Screw in the bottom bolts of fastening of a transmission to the engine.
6. Establish an arm, fixing an exhaust system to a transmission and fix it new nuts.
7. Connect a reception exhaust pipe to an inlet collector.
8. Establish a casing of the fan of a radiator.
9. At existence connect электричес a cue the socket to the sensor of level of oil.
10. Establish the forward stabilizer of cross-section stability.
11. Check that the masloslivny stopper is established in the pallet and tightened by the demanded moment. Establish the bottom mudguard of the engine.
12. Establish the air filter.
13. Fill in in the engine engine oil.
14. Connect a weight wire to the accumulator.