Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
- 4. Repair of 6-cylinder petrol SOHC engines
   4.2. General information
   4.3. Repair operations on the engine established in the car
   4.4. Check of pressure of compression
   4.5. Top dead point (VMT) of the piston of the first cylinder
   4.6. Cover of a head of the block of cylinders
   4.7. Pulley cranked shaft / quencher of krutilny fluctuations and nave
   + 4.8. Covers of a driving chain
   4.9. Driving chain
   + 4.10. Mechanism of a tension of a driving chain, asterisk and uspokoitel of a chain
   + 4.11. Drive of valves, pushers and camshaft
   4.12. Head of the block of cylinders
   4.13. Oil pallet
   4.14. Oil pump
   4.15. Replacement of a chain of a drive of the oil pump
   4.16. Drive flywheel / plate
   4.17. Replacement of sealing rings
   4.18. Bearing replacement in an end face of a cranked shaft
   4.19. Check and replacement of a support of the power unit
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






4.13. Oil pallet

GENERAL INFORMATION

Prevention

At removal of the oil pallet use of the load-lifting mechanism is necessary. At installation of the oil pallet it is necessary to use new laying and new nuts of fastening of an exhaust system.


Removal

Installation of a steel plate with cut on a partition of a motor compartment
 

Arrangement of bolts of fastening of the oil pallet
1–bolts of fastening of the oil pallet to a transmission;

2–bolts of fastening of the oil pallet to the block of cylinders of the engine

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Remove the air filter.
3. Remove an engine mudguard.
4. Remove the forward stabilizer of cross-section stability.
5. Merge from the engine engine oil.
6. At existence disconnect the electric socket from the sensor of level of the oil established in the oil pallet.
7. Remove a casing of the fan of a radiator and arrange it over a krylchatka of the fan.
8. Disconnect a reception exhaust pipe from a final collector.
9. Unscrew nuts and remove an exhaust pipe from an arm on a transmission.
10. For protection of tubes and a partition of a motor compartment establish a steel plate with cut on a partition of a motor compartment (see fig. Installation of a steel plate with cut on a partition of a motor compartment).
11. Remove the central steering draft and the steering shock-absorber.
12. Unscrew two bottom bolts of fastening of a transmission to the engine.
13. Hook on the engine slings грузоподъ the emny mechanism and raise so that the weight of the engine was perceived by the load-lifting mechanism.
14. From two parties of the engine unscrew the bottom bolts of fastening of support of the engine.
15. For access to bolts of fastening of the oil pallet slightly raise the engine.
16. Evenly and in diagonal sequence unscrew bolts of fastening of the oil pallet. Note an arrangement of bolts as they have different length (see fig. Arrangement of bolts of fastening of the oil pallet).
17. Remove the oil pallet and take it from under the car. Remove laying of the oil pallet.

Installation

PERFORMANCE ORDER
1. Clear interfaced surfaces of the oil pallet and the block of cylinders of the engine.
2. Establish the oil pallet with new laying on the block of cylinders and fix bolts, having tightened them the demanded moment.
3. Lower the engine and screw in the bottom bolts of fastening of support of the engine.
4. Remove slings of the load-lifting mechanism from the engine.
5. Screw in the bottom bolts of fastening of a transmission to the engine.
6. Establish the shock-absorber of the steering mechanism and the central steering draft.
7. Using new nuts, fix an exhaust pipe on a transmission arm.
8. Connect a reception exhaust pipe to a final collector.
9. Establish a casing of the fan of a radiator.
10. Connect the electric socket to the sensor of level of oil.
11. Establish the forward stabilizer of cross-section stability.
12. Check that the masloslivny stopper is established in the oil pallet and establish an engine mudguard.
13. Establish the air filter.
14. Lower the car and fill in in the engine engine oil.
15. Connect a weight wire to the accumulator.