Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
- 5. Repair of 6-cylinder petrol DOHC engines
   5.2. General information
   5.3. Repair operations on the engine established in the car
   5.4. Check of pressure of compression
   5.5. Top dead point (VMT) of the piston of the first cylinder
   5.6. Cover of a head of the block of cylinders
   5.7. Pulley cranked shaft / quencher of krutilny fluctuations and nave
   + 5.8. Covers of a driving chain
   5.9. Check and replacement of a driving chain
   + 5.10. Mechanism of a tension of a driving chain, asterisk and uspokoitel of a chain
   5.11. Boot of the mechanism of a tension
   5.12. Mechanism of adjustment of a camshaft
   5.13. Camshafts and pushers
   5.14. Check and adjustment of provision of camshafts
   5.15. Head of the block of cylinders
   5.16. Oil pallet
   5.17. Oil pump chain and drive
   5.18. Drive flywheel / plate
   5.19. Replacement of sealing rings
   5.20. Bearing replacement in an end face of a cranked shaft
   5.21. Check and replacement of a support of the power unit
   5.22. Oil radiator
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






5.16. Oil pallet

Removal

Arrangement of the bottom bolt of fastening of a support of the engine

Arrangement of bolts of fastening of a pipe of an oil radiator to the oil pallet

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Unscrew a bolt and lift the receiver an air inlet.
3. Remove a casing of the fan of a radiator.
4. Remove the bottom mudguard of the engine.
5. Merge from the engine engine oil.
6. Remove the forward stabilizer of cross-section stability.
7. From two parties of the engine unscrew the bottom bolts of fastening of support of the engine (see fig. Arrangement of the bottom bolt of fastening of a support of the engine).
8. Disconnect electric sockets from sensors of level and pressure of oil.
9. On models with an automatic transmission unscrew nuts and bolts and remove pipes from the oil pallet.
10. Unscrew nuts and the bolts, fixing pipes of an oil radiator to the oil pallet and an arm of an inlet collector and move them aside (see fig. An arrangement of bolts of fastening of a pipe of an oil radiator to the oil pallet).
11. Hook on the engine slings грузоподъ the emny mechanism and raise so that the weight of the engine was perceived by the load-lifting mechanism.
12. Remove the central steering draft and the shock-absorber of the steering mechanism.
13. Unscrew two bottom bolts of fastening of a transmission to the engine.
14. For access to bolts of fastening of the oil pallet raise the engine.
15. Evenly in diagonal sequence unscrew bolts of fastening of the oil pallet. Note an arrangement of bolts as they have different length.
16. Lower the oil pallet and take it from under the car. Remove laying.

Installation

PERFORMANCE ORDER
1. Clear interfaced surfaces of the oil pallet and the block of cylinders.
2. Establish the oil pallet with new laying on the engine, screw in bolts and tighten them the demanded moment.
3. Further installation is made in sequence, return to removal. Fill in in the engine engine oil. On models with an automatic transmission check oil level in a transmission.