Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
- 6. Repair of the diesel engine established in the car
   6.2. General information
   6.3. Repair operations on the engine established in the car
   6.4. Check of pressure of compression
   6.5. Top dead point (VMT) of the piston of the first cylinder
   6.6. Cover of a head of the block of cylinders
   6.7. Pulley cranked shaft / quencher of krutilny fluctuations and nave
   6.8. Cover of a driving chain
   6.9. Driving chain
   + 6.10. Mechanism of a tension of a driving chain, asterisk and uspokoitel of a chain
   - 6.11. Camshafts and pushers
      6.11.2. Check
      6.11.3. Installation
   6.12. Head of the block of cylinders
   6.13. Oil pallet
   6.14. Oil pump and driving chain
   6.15. Drive flywheel / plate
   6.16. Replacement of sealing rings of a cranked shaft
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






6.11.3. Installation

PERFORMANCE ORDER
1. Grease hydraulic pushers with pure engine oil and establish them in nests of a head of the block of cylinders.
2. Establish a persistent half ring for adjustment axial люфта a camshaft.
3. Grease necks and camshaft cams with pure engine oil and establish a camshaft in a head of the block of cylinders so that the groove on a forward flange was directed up.
4. Establish covers of bearings of a camshaft and tighten bolts of fastening of covers in the following sequence.

Four-cylinder engines

PERFORMANCE ORDER
1. In diagonal sequence tighten bolts of fastening of covers of bearings No. 2 and 4, turning each bolt on a turn half for one pass until each cover will not concern a head of the block of cylinders. Then in the same sequence tighten bolts in some stages the demanded moment. The gradual and uniform tightening of bolts is necessary for uniform compression of springs of the valve.
2. Similarly tighten bolts of fastening of covers of bearings of a camshaft No. 1, 3 and 5.

Five-cylinder engines

PERFORMANCE ORDER
1. In diagonal sequence tighten bolts of fastening of covers of bearings No. 3, 4 and 5, turning each bolt on a turn half for one pass until each cover will not concern a head of the block of cylinders. Then in the same sequence tighten bolts in some stages the demanded moment. The gradual and uniform tightening of bolts is necessary for uniform compression of springs of the valve.
2. Similarly tighten bolts of fastening of covers of bearings of a camshaft No. 1, 2 and 6.

Six-cylinder engines

PERFORMANCE ORDER
1. In diagonal sequence tighten bolts of fastening of covers of bearings No. 2, 3, 4 and 7, turning each bolt on a turn half for one pass until each cover will not concern a head of the block of cylinders. Then in the same sequence tighten bolts in some stages the demanded moment. The gradual and uniform tightening of bolts is necessary for uniform compression of springs of the valve.
2. Similarly tighten bolts of fastening of covers of bearings of a camshaft No. 1, 5 and 6.
3. Establish camshaft asterisks.