Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
- 6. Repair of the diesel engine established in the car
   6.2. General information
   6.3. Repair operations on the engine established in the car
   6.4. Check of pressure of compression
   6.5. Top dead point (VMT) of the piston of the first cylinder
   6.6. Cover of a head of the block of cylinders
   6.7. Pulley cranked shaft / quencher of krutilny fluctuations and nave
   6.8. Cover of a driving chain
   6.9. Driving chain
   + 6.10. Mechanism of a tension of a driving chain, asterisk and uspokoitel of a chain
   + 6.11. Camshafts and pushers
   6.12. Head of the block of cylinders
   6.13. Oil pallet
   6.14. Oil pump and driving chain
   6.15. Drive flywheel / plate
   6.16. Replacement of sealing rings of a cranked shaft
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






6.13. Oil pallet

GENERAL INFORMATION

Prevention

For removal of the oil pallet use of the load-lifting mechanism is necessary, and at installation of the oil pallet it is necessary to use new laying.


Arrangement of the sensor of level of oil on the oil pallet

Removal

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Unscrew a bolt of fastening of an air inlet to the forward panel of a body and remove an air inlet.
3. Remove a casing of the fan of a radiator.
4. Remove the bottom mudguard of the engine.
5. Merge from the engine engine oil.
6. Remove the forward stabilizer of cross-section stability. It is possible to leave the stabilizer of cross-section stability under the car, having unscrewed its fastening.
7. Working under the car, from two parties of the engine unscrew the bottom bolts of fastening of support of the power unit.
8. Disconnect electric sockets from sensors of level and pressure of oil.
9. On models with an automatic transmission unscrew nuts and the bolts, fixing pipes to the oil pallet.
10. Unscrew nuts and the bolts, fixing pipes of an oil radiator to the oil pallet and an arm of an inlet collector, and move pipes to the parties.
11. Hook on slings of the load-lifting mechanism for a forward eye for lifting of the engine and raise the engine.
12. Remove the central steering draft and the steering shock-absorber.
13. On models with an additional lateral part of the oil pallet on the right side unscrew bolts and remove a lateral part of the oil pallet and laying.
14. Unscrew two bottom bolts of fastening of a transmission to the engine.
15. Raise the engine and evenly in diagonal sequence unscrew bolts of fastening of the oil pallet. Note an arrangement of bolts as bolts of various length can be used.
16. Remove the oil pallet and take it from under the car. If necessary for simplification of removal of the oil pallet turn a cranked shaft of the engine.

Installation

PERFORMANCE ORDER
1. Clear interfaced surfaces of the block of cylinders and the oil pallet.
2. Establish laying on the oil pallet and establish the oil pallet on the block of cylinders. Fix the oil pallet bolts.
3. Working from the center of diagonal sequence, tighten bolts of fastening of the oil pallet.
4. Lower the engine and screw in the bottom bolts of fastening of support of the power unit.
5. At existence establish a vspomogatel a ny lateral part of the oil pallet with new laying and fix bolts, having tightened them the demanded moment.
6. Screw in the bottom bolts of fastening of a transmission to the engine.
7. Establish the central steering draft and the steering shock-absorber.
8. Further installation is made in sequence, return to removal. Fill in in the engine engine oil.