Mercedes W124

since 1985-1995 of release

Repair and car operation



W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
- 6. Repair of the diesel engine established in the car
   6.2. General information
   6.3. Repair operations on the engine established in the car
   6.4. Check of pressure of compression
   6.5. Top dead point (VMT) of the piston of the first cylinder
   6.6. Cover of a head of the block of cylinders
   6.7. Pulley cranked shaft / quencher of krutilny fluctuations and nave
   6.8. Cover of a driving chain
   6.9. Driving chain
   + 6.10. Mechanism of a tension of a driving chain, asterisk and uspokoitel of a chain
   + 6.11. Camshafts and pushers
   6.12. Head of the block of cylinders
   6.13. Oil pallet
   6.14. Oil pump and driving chain
   6.15. Drive flywheel / plate
   6.16. Replacement of sealing rings of a cranked shaft
+ 7. Major maintenance of engines
+ COOLING SYSTEM
+ FUEL SYSTEM
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS






6.16. Replacement of sealing rings of a cranked shaft

FORWARD SEALING RING OF THE CRANKED SHAFT

PERFORMANCE ORDER
1. Remove a pulley cranked a shaft / quencher of krutilny fluctuations and a nave.
2. Measure depth of installation of a sealing ring.
3. Using a screw-driver edge, take a sealing ring from a nest.
4. Alternatively, drill in a sealing ring two small openings located in diametrically противопо the false ends of a sealing ring. Screw in two self-cutting screws in the drilled openings of a sealing ring and, using flat-nose pliers, extend for heads of screws a sealing ring.
5. Clear a nest of a sealing ring.
6. For protection of working edges of a sealing ring at its installation wrap up a sticky tape an end face of a cranked shaft.
7. Dip a new sealing ring into pure engine oil and, using a tubular opravka of the corresponding diameter, establish a sealing ring in a nest on earlier measured depth.
8. Remove a sticky tape from an end face of a cranked shaft.
9. Establish a pulley cranked a shaft / quencher of krutilny fluctuations and a nave.

BACK SEALING RING OF THE CRANKED SHAFT

PERFORMANCE ORDER
1. Remove a drive flywheel / plate.
2. Measure depth of installation of a sealing ring.
3. Using a screw-driver edge as the lever, take a sealing ring from a nest.
4. Alternatively drill in a sealing ring two small openings, located in the opposite ends of consolidation. Screw in two self-cutting screws in the drilled openings of a sealing ring and, using flat-nose pliers, extend for heads of screws a sealing ring.
5. Check a condition of a surface of the cranked shaft contacting to a sealing ring. In the presence of strong wear it is necessary to replace a cranked shaft.
6. Clear a nest for a sealing ring and the surface of a cranked shaft contacting to a sealing ring.
7. For protection of working edges of a sealing ring from damage at its installation wind an end face of a cranked shaft with a sticky tape.
8. Dip a new sealing ring into pure engine oil and, using a tubular opravka of the corresponding diameter, establish a sealing ring in a nest on earlier measured depth.
9. Remove a sticky tape from an end face of a cranked shaft.
10. Establish a drive flywheel / plate.