Mercedes W124

since 1985-1995 of release

Repair and car operation

W124 Mercedes
+ Governing bodies and control devices
+ MAINTENANCE
+ 2. Maintenance (diesel engines)
+ ENGINE
+ 4. Repair of 6-cylinder petrol SOHC engines
+ 5. Repair of 6-cylinder petrol DOHC engines
+ 6. Repair of the diesel engine established in the car
+ 7. Major maintenance of engines
+ COOLING SYSTEM
- FUEL SYSTEM
   9.2. General information
   9.3. The air filter and a filtering element
   9.4. The block of adjustment of temperature of air arriving in the engine
   9.5. Fuel pump
   9.6. Fuel level sensor
   9.7. Fuel tank
   9.8. Accelerator cable
   + 9.9. STROMBERG 175 CDT carburetor
   + 9.10. PIERBURG 2E-E carburetor
   9.11. Removal and carburetor installation
   9.12. Inlet collector
   9.13. Heater of an inlet collector
+ 10. System of injection of BOSCH CIS-E fuel (KE-JETRONIC)
+ 11. System of injection of BOSCH HFM fuel
+ 12. Fuel system of diesel engines
+ 13. Fuel system of diesel engines
+ SYSTEMS OF START, IGNITION
+ 15. System of ignition of 4-cylinder petrol engines
+ 16. System of ignition of four-cylinder petrol engines
+ PRESTARTING HEATING
+ TRANSMISSION
+ 19. Mechanical transmission
+ 20. Automatic transmission
+ POWER SHAFTS
+ BRAKE SYSTEM
+ SUSPENSION BRACKET
+ BODY
+ ELECTRIC EQUIPMENT
+ CHECK OF MALFUNCTIONS

�� . Консультация юриста в оренбурге онлайн.

9.8. Accelerator cable

Removal

Arrangement of a square fixing element of a cable of an accelerator

Arrangement of brackets of fastening of a plastic clamp of fastening of a cover of a cable of an accelerator

PERFORMANCE ORDER

1. In a motor compartment disconnect an accelerator cable from a control lever a carburetor butterfly valve, previously having removed a square fixing element (see fig. Arrangement of a square fixing element of a cable of an accelerator). Take an accelerator cable through an opening in a lever arm.

2. Having compressed brackets of fastening of a plastic clamp, take a cover of a cable of an accelerator from an arm (see fig. Arrangement of brackets of fastening of a plastic clamp of fastening of a cover of a cable of an accelerator).

3. In salon of the car disconnect a returnable spring and remove an accelerator cable from the lever of a pedal of an accelerator.

4. Unscrew an adjusting nut and take a cover of a cable of an accelerator through consolidation of a cover of a motor compartment.

Prevention

Do not remove consolidation of a cable of an accelerator from a partition of a motor compartment.

5. On an external partition remove rubber consolidation of a cable of an accelerator then take a cable in a motor compartment.

Installation

PERFORMANCE ORDER

1. Installation is made in sequence, return to removal. Before connection of a cable of an accelerator with the lever of the carburetor adjust the lever and an accelerator cable.

Adjustment

Draft and carburetor lever

And – the screw;

In – a roller

Moving of the lever of a butterfly valve on the carburetor to the limiter of opening of a butterfly valve

And – the butterfly valve lever;

In – the limiter of opening of a butterfly valve

Arrangement of an adjusting nut in an arm

Arrangement of a nut of adjustment of a free wheeling of a cable of an accelerator from an accelerator pedal

PERFORMANCE ORDER

1. Start the engine, warm up it to normal working temperature and switch off it.

2. On cars with an automatic transmission disconnect a cable of management of pressure from the carburetor lever.

3. On models with the STROMBERG carburetor disconnect an accelerator cable from the lever of the carburetor and weaken the screw on the draft attached to the lever (see fig. Draft and carburetor lever). Move draft to such situation that the roller was combined with the limiter of turns of idling. Keeping draft in this situation, fix it the screw.

4. On models with the PIERBURG carburetor fix a plunzher of the executive mechanism of a butterfly valve for what press a vacuum hose and give the chance to the engine to work some seconds. Disconnect an accelerator cable from the directing lever and adjust a free wheeling of draft so that the course made 0,5 mm.

5. Connect an accelerator cable to the directing lever.

6. On cars with a mechanical transmission the assistant should press an accelerator pedal against the stop, and on cars with an automatic transmission the pedal of an accelerator is necessary for pressing so that it reached the provision of compulsory inclusion of a low gear, but did not include it.

7. The butterfly valve lever on the carburetor in this case should move to the limiter of opening of a butterfly valve. For adjustment rotate an adjusting nut in an arm (see fig. Moving of the lever of a butterfly valve on the carburetor to the limiter of opening of a butterfly valve, the Arrangement of an adjusting nut in an arm).

8. Release an accelerator pedal, thus a roller of draft should move to the limiter of turns of idling on the directing lever.

9. In this situation the end face of a cover of a cable of an accelerator should adjoin to a spring densely. For adjustment move a fixing nut on the end of a cable of an accelerator from an accelerator pedal (see fig. An arrangement of a nut of adjustment of a free wheeling of a cable of an accelerator from an accelerator pedal).

10. On models to an automatic transmission connect a cable of pressure and adjust it.